Zebra GK-420 kalibrointi

Yleensä laite kalibroi itsensä kun sen käynnistää uudelleen.

Joissain tapauksissa tämä ei auta, vaan laite tulee käsin kalibroida.

Toimi oheisen ohjeen Standard Auto Media Calibration- kohdan mukaan. Jos se ei auta, niin sitten Manual Media Calibration -kohdan mukaan:

With the printer power on and top cover closed, press and hold the Feed button for several seconds. The green status

LED will flash a number of times in sequence. The explanation at the right (Action) shows what happens when you

release the key after the start specific number of flashes and before the next flash sequence starts.

Flash Sequence Action

*

Configuration Status - Prints a detailed printer configuration status label. The label can be used

to verify printing, assist printer to computer communication configuration, maintenance,

troubleshooting, and help us with customer care communications.

*

**

Standard Auto Media Calibration - The printer detects and sets media type and media length,

and it adjusts the media sensors for optimal performance with the installed media (equivalent ZPL

command ~JC). The printer will feed one to four labels while calibrating.

Note: Users familiar with the Zebra EPL desktop printer use this Feed mode to replace power-up

AutoSensing calibration (equivalent EPL command XA).

*

**

***

Serial Port Configuration - Applies only to printers with serial interface ports.

To reset the serial port communication parameters, except for Flow Control. Press and release the

Feed button while the LED rapidly flashes amber and green.

For autobaud synchronization: Send the ^XA^XZ command sequence to the printer while the LED

rapidly flashes amber and green. When the printer and host are synchronized, the LED changes to

solid green. NOTE: No labels will print during autobaud synchronization.

*

**

***

****

Factory Defaults - Resets the printer to the factory default settings (equivalent to ZPL command

^JUN). See Appendix: ZPL Configuration on page 83 for a description of the primary

configuration settings and their associated ZPL commands. Some configuration settings are not

returned to their initial ‘out of box’ settings. Other settings are exclusively set, viewed and

controlled by programming are also reset. The performs a standard media calibration and then.a

memory defragmentation routine.

Once the printer has entered the Factory Default mode, the status light will turn amber for

three (3) seconds. During that time you may do two things: Do nothing and the printer will reset

the factory defaults automatically as described above OR press and hold the feed button to enter a

factory default reset modes for printers with a network (Ethernet, Wi-Fi or Bluetooth) printer

option (equivalent ZPL command ^JUF). Releasing the button after the first flash resets the

network factory options only (equivalent ZPL command ^JUN). Releasing the button after the

second flash sequence (two flashes) will reset the printer defaults only. Releasing the button after

the third flash sequence (three flashes) will reset both printer and network settings (equivalent

ZPL commands ^JUN and ^JUF)

*

**

***

****

*****

Print Width Adjustment - Prints a succession of boxes starting at the minimum print width and

ending in the printer’s maximum print width in 4mm increments. Press the Feed button once when

the printer has reached the desired maximum print width. Note that the printer driver and

applications can override this setting.

*

**

***

****

*****

******

Print Darkness (Density) Adjustment - Prints a succession of bar code simulation patterns

starting at the minimum darkness (print density/heat) and ending in the printer’s maximum

darkness in increments of four (4) using the ZPL darkness setting range values. Press the Feed

button once the pattern is clear and legible. Do not continue to increase the darkness setting or

bar code line widths may become distorted reducing readability. Note that the printer driver and

applications can override this setting.

*

**

***

****

*****

******

*******

Manual Media Calibration - The printer runs extensive tests to detect and set media type and

media length, and then it adjusts the media sensors for optimal performance with the installed

media (equivalent ZPL command ~JG). Manual calibration is recommended whenever you are

using pre-printed media, print on the liner or if the printer will not correctly auto calibrate. A

graphical profile of the media sensing will print. See Manual Calibration on page 66 for more

details and considerations.

If the Feed button remains pressed after 7th flash sequence cycle finishes, the printer exits the

configuration mode when the Feed button is released.